Weather Monitoring

From Agri4castWiki
Revision as of 15:13, 13 October 2017 by Stefannieme (talk | contribs) (Forecasted weather)
Jump to: navigation, search

General description

The role of weather monitoring within the MCYFS

The weather monitoring module is one of the five modules of the MCYFS and can be split in four procedures.

  1. Acquisition
  2. Interpolation
  3. Aggregation
  4. Climatology and analysis

The output of the weather monitoring module is used in two ways: firstly, to derive agro-meteorological indicators for a direct evaluation of alarming situations such as drought, extreme rainfall during sowing, flowering or harvest etc., and secondly, as input to the crop simulation module to simulate crops behaviour and to evaluate the effect of weather on crops yield.


Weather Station, Garreg Fawr, Aberdaron

Observed weather

Every day raw data of at least 4200 synoptic weather stations that regularly collect and supply one or more meteorological variables are acquired over Europe and its neighbourhood and are added as raw data to the station weather database. The variables collected include air temperature, precipitation, radiation, air humidity, and wind speed. All incoming data are checked for errors and dubious values, such as e.g. air temperatures outside a realistic range. The incoming data are then converted to daily values that fit in a uniform station weather database. Some variables required for the crop simulation module are not at weather stations, or not in sufficient density. Such variables, like solar radiation or evapotranspiration, are derived from the measured data and also added to the database.

Supercomputer at ECMWF

Forecasted weather

Besides observed weather data also weather forecasts are loaded into the system so that crop development and biomass accumulation can be simulated into the future (see crop simulation module), reaching closer to the end of the crop season, compared to using observed weather, and advancing crop yield forecasts along the season (see yield forecasting module).

Six data products from ECMWF are loaded into the system:

  • ERA-Interim (ERA)
  • Analysis model (HIS)
  • Deterministic forecast model (OPE)
  • Ensemble Prediction System (ENS)
  • Monthly forecast model (ENSEXT)
  • Seasonal forecast model (SEAS)

These products have a different number of forecast days (forecast depth) and a varying number of possible realizations called 'members'. Different members can be thought of as model runs with a slightly different initialization and thus slightly different results, but with equal validity. Similar to observed weather, meteorological variables such as air temperature, precipitation, and solar radiation are directly retrieved from the forecast data. Additional parameters are calculated from these variables within the MCYFS.


Interpolation from weather stations to 25 x 25 km regular climate grid.

Observed weather

Observed weather is aquired from weather stations that have an irregular distribution and density in space, e.g. over Europe. Weather station data of a single station are representative for the location of that station only. To construct weather data for locations in between stations a conversion is needed. Interpolation (constructing new data points within the range of a discrete set of known data points) is one of the methods to do this. In the MCYFS this procedure is used to convert irregular distributed station data to regular distributed data. The regular distribution is organized as a grid with side by side grid cells of 25 kilometre width and 25 kilometre length that cover the entire region of interest (e.g. Europe)and is called the regular climatic grid. The interpolation is managed by a sub-system called CGMS.

Interpolation from 0.5 x 0.5 degrees grid to 25 x 25 km regular climate grid.

Forecasted weather

Weather forecast data come already as spatial fields, not point data as observations, but in varying spatial resolutions and projections that are different from the climatic regular grid used in the MCYFS. Therefore the data are interpolated from a 'source' grid to a 'target' grid that is equal to the climate grid. This specific interpolation procedure is also called 'downscaling' because for some models it converts lower resolution (source) data into higher resolution (target) data.


Example of 4 different administrative levels in combination with landcover type 'arable land' on 25 x 25 km grid.

The primary results of the interpolated observed stations weather and downscaled forecast weather is grid weather. To answer questions like:

'What was the average temperature in France during the last week for locations where winter wheat is grown?'

grid weather data are aggregated to different types of regions while weighing each gridcell for the area covered by a certain landcover type. Observed grid weather and forecasted grid weather of the ECMWF ERA, HIS and OPE models are aggregated to different levels of administrative regions for a number of landcover types. Optionally the same type of aggregations is done for agri-environmental zones too.

Altogether the aggregation procedure results in many aggregated weather data sets based on the type (Observed, ERA, HIS, OPE), regions and landcover types.

Climatology and analysis

Long term average temperature over period Januari-June on a 25 x 25 km resolution.

Within the MCYFS climatology is considered as long term average values of weather indicators. It is essential to understand how current weather conditions relate to the normal situation.

Long term average daily values are calculated over the years in the archive for all spatial resolutions defined in each regional window.

Besides averages of the basic indicators (such as daily precipitation, daily temperature and daily solar radiation) additional statistics are calculated for instance the probability of having a rainy day defined as a day receiving more than a certain amount of rainfall (5, 10, 15 mm). This makes it possible to compare extreme weather event of the current year with extreme weather events in the past. For instance compare the number of rainy days (more than 5 mm) of last month with the average number of rainy days (more than 5 mm) in all according historic months.