ISW

From Agri4castWiki
Jump to: navigation, search


Introduction

To estimate initial soil water content for crop simulations, the implemented approach is to start a water balance long before the actual crop simulation. Using this approach, recharge of the soil moisture by rainfall and water use of a pseudo crop simulation or bare soil will help to find a more representative estimate of the soil moisture level when the actual crop simulation for the year of interest starts.

The pseudo crop simulation has been implemented by a simplified model which only implements leaf area index dynamics, root growth and evapotranspiration. Initial soil water content for the pseudo crop simulation starts with a full soil moisture profile by default as for the RUK window, or can be provided by the database (table SOIL_INITIAL_WATER_ALL, attribute WAV_ISW). For root growth and evapotranspiration modules from WOFOST were taken and parameterized for a typical cereal crop. The leaf dynamics are described by the Canopy Structural Development Model (CSDM, Koetz et al., 2005) which describes LAI growth and senescence by a combination of a logistic and exponential curve. The difference with the original CSDM is that the pseudo crop uses the day number as its internal state to calculate LAI, while in the original version a temperature accumulation is used. Finally, a loose coupling to the soil water balance has been established which allows switching the crop simulation on and off while still keeping the integrity of the soil moisture balance intact. At the end of the pseudo crop run, the amount of available soil moisture is updated in the SOIL_INITIAL_WATER_ALL table (WAV parameter). Thereafter, the BIOMA crop simulation is run, using more realistic initial soil water content.

Architecture

The ISW is developed in python. To be able to run the package in parallel, it is connected to a tasks administration system that should be configured before estimating initial soil water content. Each instance of ISW picks up a pending task. Once picked up, it cannot be handled by another instance. Together all instances handle the pending tasks one by one until all tasks of the task list are finished. The tasks can be created by the COPdate package as in the operational production line for the RUK window, or inserted during a manual set-up as in the operational production line for the EUR window.

The ISW is built using components already available in the python implementation of WOFOST-PCSE. Below figure shows the relationships between the components in the ISW. At the highest level is the ISW interface, which arranges some administrative matter and exposes its interface. Within ISW, the SoilCropSimulation object takes care of the actual simulation loop by making the appropriate calls to the Timer, AgroManagement, FakeCropSimulation and WaterbalanceFD routines. This includes the initialisation step, the calculation of rate variables, integration of states and the finalisation step.

ISW components figure.jpg

An overview of the components that are used by ISW and their location in the ISW package:

Component Component position in ISW package
SoilCropSimulation isw_determinator.soilcropsimulation.SoilCropSimulation
Timer isw_determinator.timer.Timer
AgroManagement isw_determinator.agromanagement.AgroManagementFakeCrop
FakeCropSimulation isw_determinator.fakecrop.FakeCropSimulation
Root_dynamics isw_determinator.crop.root_dynamics.WOFOST_Root_Dynamics
Evapotranspiration isw_determinator.crop.evapotranspiration.Simple_Evapotranspiration
CSDM_leaf_dynamics isw_determinator.crop.leaf_dynamics.CSDM_Leaf_Dynamics
WaterbalanceFD isw_determinator.classic_waterbalance.WaterbalanceFD

The ISW package has several dependencies which are:

  1. The numerical python package ‘numpy’.
  2. The database abstraction package ‘SQLAlchemy’
  3. A database driver for connecting with the ORACLE that stores the CGMS schema and data. In this case cx_Oracle driver is used.

ISW algorithms

There are two sets of algorithms implemented, one for winter wheat with vernalisation in the EUR window, and one for spring- and winter wheat in the RUK window.

EUR

The EUR implementation of the ISW consists for two components:

  1. The soil water balance which is an exact implementation of the CGMS/WOFOST soil water balance for free drainage conditions.
  2. The soil evaporation as is done by CGMS/WOFOST

Given that the they are identical to the WOFOST components, we refer to the WOFOST documentation.

RUK

The RUK implementation of the ISW consists for four components:

  1. The soil water balance which is an exact implementation of the CGMS/WOFOST soil water balance for free drainage conditions.
  2. The root dynamics module which simulates linear root growth up to a maximum depth as is done by CGMS/WOFOST.
  3. The soil evaporation and crop transpiration as is done by CGMS/WOFOST with a reduction in transpiration based on the soil moisture content and the drought sensitivity of the crop.
  4. The leaf dynamics module which is based on prescribed LAI trajectory based on the Canopy Structural Development Model (Koetz et al., 2005). A consequence of using a fixed LAI trajectory is that there is no leaf death as a result of moisture stress which is simulated by WOFOST.

Given that the first three components are identical to the WOFOST components, we refer to the WOFOST documentation. The Canopy Structural Development Model (CSDM) is used to define a fixed LAI trajectory based on combination of a logistic function to describe the increasing part of the LAI trajectory, and an exponential function describing the decreasing part of the LAI trajectory. The difference with the original CSDM is that in our implementation the thermal time as driving variable has been replace with the day number. This way we could easily define a fixed length growing season without any calibration of thermal time. Our implementation of the CSDM is the following:

CSDM LAI trajectory formula.jpg

Where LAIt is green leaf area index on day number t, the latter is the day number counted since the start of the CSMD model. See the figure below for an example of the LAI trajectory simulated by the CSDM. We have chosen for a relatively low maximum LAI in the model assuming relatively extensive crop managements which leads to relatively thin canopy cover. Moreover, a very high LAI would lead to high water extraction which would be unrealistic given general yield levels in Russia and Kazakhstan.

CSDM LAI trajectory figure.jpg

Different rules apply for spring wheat and winter wheat. For winter wheat ISW takes the sowing date as provided by table CROP_CALENDARS and calculates the start date of the ISW by subtracting 15 days (assuming fallow land) and another 120 days for the cycle of the pseudo crop simulation. For spring wheat ISW assumes a fixed sowing date of 15 May in the previous year and simulates 120 days of the pseudo crop cycle. Next it simulates a bare soil through the remaining period up till the sowing date provided by the CROP_CALENDARS table. At the end of the pseudo crop simulation, when the ISW reaches the sowing date of the CGMS/WOFOST, the state of the soil moisture is transferred to CGMS/WOFOST through the WAV parameter in table SOIL_INITIAL_WATER.

Configuration

By default, the pseudo crop simulation is initialized with a full soil profile. Alternatively, the initial soil water content for the pseudo crop simulation is read from table INITIAL_SOIL_WATER_ALL, attribute WAV_ISW. This attribute should be filled by an external procedure. In the case of the the winter wheat crop parametrization with vernalisation, WAV_ISW is set the long term average grid specific end-of-season WAV of winter wheat crop simulations.

Parameters used for the CSDM model (see equation above) and there representation in the model code of the ISW.

Parameter Identifier Description Default value Unit
CSDMmin CSDM_MIN Minimum LAI at the start 0.15 -
CSDMmax CSDM_MAX Amplitude of LAI, roughly the maximum value of LAI 4 -
A CSDM_A Shape parameter in the exponential model 0.085 -
B CSDM_B Shape parameter in the logistic model 0.045 -
t1 CSDM_T1 Time of maximum increase of logistic model 40 Days
t2 CSDM_T2 Total length of the growing season (LAI=0) 120 Days

Other parameters used for the ISW. These values are taken from a spring-wheat crop and are hardcoded in the model.

Parameter Description Default value Unit
KDIF Extinction coefficient for diffuse visible light 0.6 -
CFET Correction factor evapotranspiration 1.0 -
DEPNR Crop group number for soil water depletion 4.5 -
RDI Initial rooting depth 10 cm
RRI Maximum daily increase in rooting depth 1.2 cm
RDMCR Maximum rooting depth of crop 120 cm